모든 제품
담당자 :
June Zhao
2W Non-maintained emergency packs with 3 hours duration and 5 years warranty
무료 샘플과 쿠폰을 받으려면 연락하세요.
왓츠앱:0086 18588475571
웨이 채팅: 0086 18588475571
스카이프: sales10@aixton.com
만약 당신이 어떠한 관심도 가지면, 우리가 24 시간 온라인 도움말을 제공합니다.
x제품 상세 정보
| 정격 입력 전압 | 220-240Vac 50Hz /60Hz | 비상 전력 | 2W (특별화 할 수 있습니다) |
|---|---|---|---|
| 비상시 | 180min (자격화 할 수 있습니다) | 보증 | 5년 |
| 부하 출력 전압 | 10-60Vdc | 작동 온도 | 0 ℃ ~ 50 50 |
| IP 등급 | IP20 | 배터리 유형 | 라이프PO4 6.4V 1800mAh |
| 강조하다 | 2W LED emergency driver,non-maintained emergency packs 3 hours,emergency driver with 5 years warranty |
||
제품 설명
2W Non-maintained Emergency Packs with 3 Hours Duration and 5 Years Warranty
Product Overview
Constant power output LED emergency power supply with wide output voltage range, featuring LifePO4 battery technology with 5-year warranty.
- Constant power output LED emergency power supply with wide output voltage range
- Input relay switching
- High safety, high performance, long life LifePO4 battery
- Integrated battery management system
- Standard and self-test emergency packs
Technical Parameters
| Charge Part | ||
|---|---|---|
| Model No. | KE036-02AM180HB | |
| Rated input voltage | 220-240Vac 50Hz/60Hz | |
| Rated input current | 0.06A Max. @230Vac | |
| Input inrush current | 10A(Twidth=100us 50% Ipeak) @230Vac (Cold start at full load) | |
| Power factor | ≥0.5@230Vac | |
| Input power | <4W@230Vac | |
| Battery charging current | 250mA Max. | |
| Battery charging time | 24 hours Max. | |
| Emergency Part | ||
| Operating mode | Emergency mode | |
| Load type | LED | |
| Emergency power | 2W | |
| Emergency time | 3 hours | |
| Load output current | 200-30mA | |
| Load output voltage | 10-60Vdc | |
| Battery | ||
| LifePO4 (The battery capacity meets the emergency time at 25℃) | 6.4V 1.8Ah | |
| Battery warranty | Warranty 5 years @25℃ | |
Product Dimensions
Unit: mm
Wiring Diagrams
Basic wiring diagram
Fig A: With LED driver and LED module
Fig B: With LED module
Fig C: Loop in & out with LED module
Operation Instructions
Manual Test Mode
- Before installation, set Pin short: Manual Test
- Connect the wire according to the wiring diagram
- L, N power on, Switch on S1. Then the load lamp turns on, the emergency driver indicator light turns green, emergency power supply is normal charging. Turn off Switch S1; the load lamp turns off
- Emergency Simulation: Switch on, the load lamp turns on, press the switch (TEST SWITCH), then switch to emergency mode, the indicator light of the emergency driver will be extinguished. Release the switch (TEST SWITCH), then the lamp is powered by LED driver, the indicator light will turn on
Automatic Test Mode
- Before installation, set Pin open: Automatic Test
- Connect the wire according to the wiring diagram. Remove the test switch on the LED Emergency Driver
- L, N power on, start the clock, and perform a periodic self-test. To replace the battery, turn off the power supply, and re-time
Battery Application Notice
- The battery should be recharged and discharged semiannually in normal use conditions
- Do not connect to the circuit when the battery is not in use to prevent over-discharge of the battery due to self-consumption of the circuit board
- Please keep the battery away from the heat source when installing and using, and only be allowed to be used in a certain working temperature range
- The battery should be stored in a cool and dry environment
- After long-term storage, the battery is cycled every 6 months as required
- AC power is off, and the clock lasts for 7 days. Power on and re-time. To replace the battery, turn off the power supply, and re-time
All parameters are tested on the input voltage 230VAC, environment temperature 25℃, unless otherwise specified.
추천된 제품